support@tooltra.com
๐Ÿ“ฆ Free Shipping & 30-Day Hassle-Free Returns
Ignition coil and fuel injector tester with battery clip cable and test leads
Misfire or rough idle? Test the coil or injector before you buy a new one
Six functions in one tool: ignition coils, fuel injectors, solenoid valves, stepper motors, PWM signal and volt/ohm meter
How the actuator tester works
How to use the tester in 5 steps
Reading the result: part responds vs check further
Color screen test modes
Front panel controls of the actuator tester
What's in the box
Specifications and size, 6.1 x 3.7 inches
What the tester does and doesn't do
Bench-test parts before you install them
Ignition coil and fuel injector tester with battery clip cable and test leads
Misfire or rough idle? Test the coil or injector before you buy a new one
Six functions in one tool: ignition coils, fuel injectors, solenoid valves, stepper motors, PWM signal and volt/ohm meter
How the actuator tester works
How to use the tester in 5 steps
Reading the result: part responds vs check further
Color screen test modes
Front panel controls of the actuator tester
What's in the box
Specifications and size, 6.1 x 3.7 inches
What the tester does and doesn't do
Bench-test parts before you install them

Ignition Coil & Fuel Injector Tester โ€“ 6-in-1 Automotive Actuator Driver with LCD Screen for Solenoid Valves, Idle Stepper Motors & PWM Signals, 12V/24V

Regular price $119.90 $144.99 ( Save 17%)
/
+Free Shipping

Free Tracked Shipping

30-Day Return Guarantee

24/7 Customer Support

Guaranteed Safe Checkout

DESCRIPTION

Misfire, rough idle or stalling? Test the part before you buy a new one.

Coils, injectors and idle motors aren't cheap, and swapping parts until the problem goes away gets expensive fast. This tester powers the part directly, the same way the engine computer does, so you can see, hear and measure whether that coil, injector, valve or idle motor responds. It helps you spot an electrical problem with the part before you replace it.

Hook it up to a 12V battery, plug in the part, pick the test on the screen and press START.

Why choose this actuator tester?

  • Know before you buy. Check a coil, injector or idle motor on the bench before you order a replacement or pay for one at the shop.
  • Separate a bad part from a wiring problem. If the part works on the tester, look at the wiring, connector or control signal instead.
  • Six functions in one case. Ignition coil test, injector test, solenoid valve test, stepper motor drive, PWM signal generator and a built-in voltmeter/ohmmeter.
  • Easy to read. A color screen shows the test mode and every setting, so you always know what the tester is doing.
  • Check used and junkyard parts. Test a part before you spend time installing it.

Key features & benefits

  • Ignition coil test: fires 2-wire coils at an adjustable rate (1โ€“20 Hz) so you can check for spark with a spark tester. 4-wire coils are driven from the PWM OUT mode, following the manual's wiring diagram.
  • Fuel injector test: pulses 12V gas injectors and 12V/24V diesel solenoid injectors (1โ€“20 Hz, adjustable pulse width). Listen for a steady click and read the current draw on screen.
  • Solenoid & fuel metering valve test: drives duty-cycle valves (1โ€“500 Hz, 1โ€“70% duty) so you can see and hear them work.
  • Stepper motor drive: turn idle air motors, gauge motors and headlight leveling motors left and right with two buttons.
  • PWM signal generator: adjustable frequency (1 Hzโ€“100 kHz) and duty cycle (0โ€“100%) to simulate duty-cycle sensor signals.
  • Built-in multimeter: DC voltage up to 36V and resistance up to 1 Mฮฉ. Check an injector's or coil's resistance against your service manual.
  • Adjustable output voltage: 1.25โ€“11.5V with its own LED readout, for parts that need a lower supply voltage.
  • Runs from the vehicle battery: battery clip power cable included. Works on 12V, and on 24V for 24V parts.

Perfect for

  • DIY owners chasing a misfire, rough idle, hard start or idle that hunts up and down
  • Checking a coil, injector or idle motor before you buy a replacement
  • Testing used, rebuilt or junkyard parts before installing them
  • Cars, pickup trucks, motorcycles, boats and light-duty diesels
  • Small shops and mobile mechanics who want one bench tool for actuators

How to use

  1. Engine off. Unplug the part's electrical connector from the vehicle, or remove the part and put it on the bench.
  2. Power the tester. Clip the power cable to a 12V battery (red to +, black to โ€“). Use 24V only for 24V parts. The red VIN+ light stays on.
  3. Connect the part. Use the included test leads to connect the part to the matching ports, following the wiring diagram in the manual.
  4. Pick the test. Press MODE until the screen shows the right test: Injector, Ignition Coil, Valve, Step Motor, PWM Out or Voltage/Resistance.
  5. Run it. Press START. Turn the knobs to set the speed and pulse width. Watch, listen and read the screen. Press STOP when you're done. For stepper motors, use the left and right motor buttons instead.

Reading the results

Part Part responds Check further
Fuel injector Steady clicking at the set speed; current reading on screen No click, or 0.00 A: recheck the leads and the test settings first. If it's still dead, the winding may be open or the injector stuck. Check its resistance with the ohmmeter.
Ignition coil Strong, regular spark at a spark tester (not included) No spark or a weak, irregular spark: suspect the coil.
Solenoid / fuel metering valve Clicks or moves as you change the duty No response: suspect the valve.
Idle / stepper motor Shaft moves in and out (or turns) when you press left and right No movement or jerky movement: suspect the motor.
Resistance Reading close to the value in your service manual OL (open) or far from spec: winding is open or shorted.

If the part works on the tester but not in the vehicle, the problem is more likely the wiring, the connector or the control signal. A part that responds can still have a flow, spray-pattern or mechanical fault: the tester checks the electrical side only and does not measure fuel delivery.

Compatibility

Works with:

  • 12V ignition coils (2-wire and 4-wire), 12V gasoline fuel injectors
  • 12V and 24V diesel solenoid injectors and fuel metering valves (24V parts need a 24V supply)
  • Duty-cycle solenoid valves, idle stepper motors, gauge stepper motors, headlight leveling motors
  • Duty-cycle (PWM) sensor signal simulation

Won't work with:

  • Piezo diesel injectors
  • High-voltage hybrid or EV components
  • Reading trouble codes: this is not an OBD2 scanner and does not plug into the diagnostic port

Compatibility depends on the part's voltage, pin layout, type and current draw, and on using the right wiring diagram. Not sure about your part? Send us the part number or a photo of its connector before you order.

Important notes

  • Test with the engine off and the part unplugged from the vehicle wiring. The tester replaces the engine computer's signal; it does not run alongside it.
  • Ignition coils make high voltage. Use a spark tester, keep hands off the coil output while it fires, and test away from fuel and fuel vapors.
  • Never fire a fuel injector near sparks or a running ignition coil.
  • The voltmeter is limited to 36V DC. Don't reverse the leads.
  • This tester shows whether a part works when it's powered. It does not diagnose wiring, sensors or the engine computer on its own.
  • Some parts need a specific connection or pulse setting. Follow the manual and your vehicle's service information. Compatibility can vary by model.
  • Basic electrical knowledge is helpful. If you're not comfortable connecting test leads, ask a qualified technician.

Specifications

  • Model: QDB-4A
  • Power input: 12โ€“24V DC via battery clip cable (max 26V). No internal battery.
  • Drive output: up to 2A
  • Adjustable output (V-ADJ): 1.25โ€“11.5V, up to 1.5A
  • Fuel injector test: 1โ€“20 Hz, pulse width 0โ€“3,000 ยตs
  • Ignition coil test: 1โ€“20 Hz, pulse width 0โ€“1,000 ยตs
  • Solenoid valve test: 1โ€“500 Hz, duty 1โ€“70%
  • PWM signal / PWM drive: 1 Hzโ€“100 kHz, duty 0โ€“100%
  • Stepper motor drive: up to 1.5A
  • Multimeter: DC voltage 0โ€“36V, resistance 0โ€“1 Mฮฉ
  • Display: color LCD for test settings, plus LED readout for the adjustable voltage
  • Size: approx. 6.1 ร— 3.7 in (15.5 ร— 9.5 cm)
  • Operating temperature: 32โ€“131ยฐF (0โ€“55ยฐC)

What's included

  • 1 ร— Actuator tester
  • 1 ร— Battery clip power cable
  • 3 ร— Alligator clip test leads
  • 3 ร— Fuel injector test wires
  • 4 ร— Universal wires
  • 3 ร— Banana plugs
  • 2 ร— Stepper motor plugs
  • 1 ร— Sensor wire
  • 1 ร— User manual (English)

FAQ

Can it read check engine codes?

No. It is not an OBD2 scanner. Use a code reader to find which cylinder or circuit is flagged, then use this tester to check the part itself.

Do I have to remove the part from the engine?

Not always. You must unplug the part's connector from the vehicle wiring and connect the tester instead. Many coils and idle motors can be tested in place; injectors are often easier to check on the bench.

What does it need for power?

A 12V battery, like your vehicle battery or a spare 12V battery. Use 24V only for 24V parts. The battery clip cable is included; there is no internal battery.

Will it work on my diesel?

It drives 12V and 24V solenoid-type diesel injectors and fuel metering valves. It does not drive piezo injectors. If you're unsure, send us your part number.

Is it hard to use?

You pick the test with the MODE button and press START. The screen shows the settings, and the manual includes a wiring diagram for each test. Some basic electrical knowledge helps.

How long does shipping take, and what if it doesn't work for me?

Orders ship free with tracking. See our Shipping Policy for current delivery times and our Refund Policy for return terms.

Test the part, see the result, and only replace what's actually bad.

-3
Ignition coil and fuel injector tester with battery clip cable and test leads

Ignition Coil & Fuel Injector Tester โ€“ 6-in-1 Automotive Actuator Driver with LCD Screen for Solenoid Valves, Idle Stepper Motors & PWM Signals, 12V/24V

What are you looking for?